How a Polyurethane Breaker Wiper Seal Protects Hydraulic Parts

Author: KEDIAS

Source: Office

Time: 2026-11-09


At KEDIAS Sealing, we supply the polyurethane breaker wiper seal that sits at the rod end of a hydraulic breaker or a cylinder and keeps dirt out of the hydraulic system. The seal, also called a dust seal, scrapes dust, sand, mud and moisture from the piston rod before the rod retracts. Without it, those particles reach the rod seal and the cylinder bore, where they cause scratches, leaks and a slow loss of pressure. The KB-2000 is a NOK breaker seal made for this protective duty.

Why the Wiper Seal Matters

A hydraulic breaker works in dust, mud and rock chips, and the rod moves in and out thousands of times a shift. Every stroke carries a thin film of oil and whatever is on the rod. A wiper seal removes the contamination at the entry point, so the internal seals see clean oil. When the wiper is worn or damaged, the first sign is often a dirty rod or a small leak at the front end, followed by a drop in breaker performance. Replacing the wiper early is much cheaper than rebuilding the cylinder.

Material and Design

The seal is made from high quality PU and NBR rubber compounds. The material gives a balance of flexibility, abrasion resistance, low temperature toughness and anti aging performance, so the lip keeps scraping through continuous reciprocating motion and outdoor conditions. The NOK structural design optimises the sealing surface, the smoothness and the hardness to reduce wear and leakage, and the cross section is shaped to follow the rod without turning or lifting. The fastening detail keeps the seal stable during installation and use.

Where the Seal Fits

The main applications are excavator boom, arm and bucket cylinders and hydraulic breaker cylinders. The seal is used across many machine brands, including Caterpillar, Komatsu, Hitachi, Volvo, Doosan, Hyundai and Sany, and the correct part should be selected by the machine model and the cylinder size rather than by appearance. Mining, rock breaking, road construction, municipal work and demolition are the typical sites, because those are the jobs with heavy dust and mud. A seal that fits the groove but not the rod diameter will leak or wear quickly.

Installation Notes

Clean the rod and the seal groove before fitting a new wiper. Check the rod surface for nicks and burrs, because a sharp edge can cut the new lip as it slides in. Lubricate the seal with clean hydraulic oil, seat it square in the groove and protect it from sharp tools during assembly. After the repair, cycle the cylinder a few times and check for a leak at the rod end. A wiper that is installed dry or at an angle can roll out of the groove on the first stroke.

Maintenance and Stock

Keep a spare wiper seal for the machines in the fleet, because a small seal can stop a breaker for a day if it is not in stock. Inspect the rod and the wiper at each service and replace the wiper when the lip is worn, hard or torn. Store the seals in a cool, dry place away from direct sunlight and do not hang them on a hook, because a deformed seal may not seat correctly. A simple stock plan for the most used seals reduces downtime across a site.

Seal Selection

Buyers sometimes send only the machine brand and not the cylinder model. In that case, the rod diameter, the groove width and the seal height are the details that decide the part. A photo of the old seal next to a ruler is often enough to identify it. The material also matters: a standard PU lip suits most site work, while a low temperature grade is used where the machine runs in cold conditions.

Working With KEDIAS

Our product range covers hydraulic breaker seal kits, excavator seal kits, diaphragms, polyurethane dampers, rod seals, buffer seals, dust seals, gas seals and O rings for many breaker and excavator brands. Buyers who need a polyurethane breaker wiper seal can send the machine model, the cylinder size, the part number and the quantity. Our team will confirm the material, the dimensions and the packing before quoting. If a part number is not in the current list, a sample or a drawing helps us match the seal.

Send us the machine model and the seal position, and we will reply with the recommended part, the quotation and the next steps. A clear part reference at the start is the simplest way to avoid a seal that fits the groove but not the rod.

Get A Quote

Note: Please leave your contact information, our professionals will contact you as soon as possible!

Submit Now

Sorry, there is currently no content in the current column

You can check other sections

License